Proudly Made in America (Complete Tee post Driver System)
  (Bullet Point, Driver-5 is our proven jewel. However this Driver has a lot of parts & labor that goes with making it into a great T-Post Driver. Our Driver-3's & 4's can do 85% of what a Driver 5 can accomplish and the 4's has way less labor in our manufacturing. We have priced our Driver 4's accordingly. The Dr-3 is for the experienced operator and we can offer it for less than $90. + add shipping (below are the details.) Please have a look at all Drivers (Click on lettering below each Picture to expand info.) to see witch Driver will do the best job for your operation.Below we explain how to measure out your bucket to choose the right Front/Clamp, witch causes less preperation for you and gives you a good fit to your tractor. We do have Mike on-call for ?s at your convenience 1-580-747-9288  
   First up Dr-3 info. 3 is the Bare Bones of our Drivers for the salty operators that know their land and what their tractor can and can't do. We picked out a Front/Clamp 1-inch opening and 6-1/2 inches deep. If you have your tractor bucket’s two measurements at the end of your order is the comment/section place those two measurements in there and we will fit your bucket the closest that we have. Also when looking at Driver-3 click-on picture and scrole down to read more on that Driver.(Measuring out your Bucket)-If your tractor bucket has an added protective plate welded-in across the scraper's edge or digging edge. We like to help you get a good fit for the Front Clamp, witch will have you Drilling the needed 1/2" hole into the thinner part on your bucket. Then two measurements are needed. First measurement:  measure the width not length of that thick plate underneath so 4" or maybe up to 6". We add another 1/2" for when the 1/2hole is drilled getting your drilled hole into the thin part of your bucket. So our numbers are 4-1/2" or 6-1/2" The second measurement: The total thickeness of your bucket. Now where you just measured that underneath plate now measure that thickness of that underneath lip and add another 1/4", so that total combined is like 7/16" or 1/2" or 5/8". When you have thoughs two measurements then it is time to go shopping Click-on Driver-3-4 or 5 prices mark right below Top Heading. Our Front Clamps can be left sticking out or pushed out that doesn't bother anything. We send washers to shore/up or shim up between your bucket and Front Clamp. So let's make this easy on us both? If needed call us or add your two measurements for us to compare then in the (Order Comments box witch is at the end of your ordering your Driver and Clamp.)  Either way is fine if you feel this step is needed to insuring you get a good fit on your Clamp Size. Our 3/4" gapped and 4½"deep Clamp is our standard Clamp to buy. If thicker plate please move to the next picture. The idea is to get past the thicker part of your bucket to drill out this ½"hole. Just a note (No one has to become a member, just click on our to-buy button, thank you.www.metaltpostsindallastx.com website has better graphics and our video that shows off our Drivers. 
Drive your t-posts one every minute. Driver-5 is faster and has more math, technology to automatically hold and release new or clean posts up into driver barrel. As to Driver-4 will take on old beat-up and new posts. You will have to close the bottom clamp just firmly to hold each tee post up in the barrel. The advantages of both are. You are way faster because you can see what you are doing and no one has to be underfoot. You already have the most costly part to this work equation and that is your Hydraulic Tractor-Loader. The safety and quickness for this simple tool are unbelievable. We have also designed our Drivers to allow tee post placement in your finished or built fencerow. As far as we know we have the only Driver that can be raised up over your fencerow and press in a new tee post where needed.  Our State College has driven 20 miles of tee posts with one of our Driver-5's in eighteen different work sights. The crew had nonbelievers and thought they would need to improve on this Driver-5. These men suspicions have been proven wrong and our Driver-5 works on. We have added a Tee Post Puller on the bottom if you need one for convenience and our last invention is our Quick Gage that has an extended pin and swing-set-chain for adjustment to match your fence high. When chain weight touches the Ground you are done driving in that tee post. Be prepared to be amazed. Video on  

     You-tube =  http://www.youtube.com/watch?v=7oPIomYkqow

                          Driver-5 with 3/4 Front Clamp fits 85% of all Buckets 
We will ask you to please drill a 1/2 inch hole through your bucket when using any of our Clamps. The reason for a hole is that this firmly mounts our Clamps and Drivers onto your bucket. Driving in T-posts we found to be extremely violent. Our 3/4 Front-Clamp at 4 1/2 inches back or off the cutting edge mounts to 95% of all New Farm and Industrial Buckets. If you need a deeper Clamp 5 inches deep from the cutting edge call 580-747-9288. We have added washers in case your bucket is a little thinner. If ever you get or use a heavier bucket you probably wouldn't need to buy another Clamp. We do sell a smaller 1/2 inch gapped Front-Clamp. (recap) Having a lighter bucket may be the better option to go with the 3/4 Front-Clamp? That does mean you will have to drill or cut a 1/2 hole in your bucket 4 1/2  inches center from the edge. The sweet spot for that 1/2 inch hole and Clamp is on the right side of your bucket's cutting edge or on the same side as your hand hydraulics levers. (Universal-Clamp) is designed for the-off-the-wall-idea that has a one-of-a-kind-mounting. Side-Mounting our Universal-Clamp to your bucket takes two 1/2 inch drilled or cut holes. This mounting could work the warble-joint on the Driver's knuckle to the max. Timing our Driver onto your bucket is probably needed and doable with help from our Timing-Paper to help get you started. The way to check out all our Drivers and Prices is at the top of your side-bar.  (C)
 
    If purchasing off the Internet is unappealing then send a check for your preferred Driver & Clamp then add $20 for shipping (For U.S. customers only) (Bucke-Tee IIC)  (Bucckdriver.com 1618 Indian Dr. Enid, Ok 73703) Thanks, Z

Items on sale

DRIVER-3 (BAR3/BON3S)
$89.70
In Stock